How To Remove Cover Of The Gear Shift Of A 2010 Toyota Tacoma

By Brody Leyton
March 17, 2023

Table of Contents

“Step-by-step guide to easily remove the gear shift cover of your 2010 Toyota Tacoma.”

Introduction

To remove the cover of the gear shift of a 2010 Toyota Tacoma, you will need to follow a few simple steps. This process can be completed with basic tools and should take only a few minutes to complete. In this guide, we will walk you through the steps required to remove the cover of the gear shift on your 2010 Toyota Tacoma.<h2 id="wpaicg-step-by-step-guide-removing-the-cover-of-the-gear-shift-of-a-2010-toyota-tacoma”>Step-by-Step Guide: Removing the Cover of the Gear Shift of a 2010 Toyota Tacoma

If you’re looking to remove the cover of the gear shift of your 2010 Toyota Tacoma, you’ve come to the right place. This step-by-step guide will walk you through the process, so you can get the job done quickly and easily.

Step 1: Locate the Screws

The first step is to locate the screws that hold the cover in place. In most cases, there will be two screws located at the base of the cover. You may need to use a flashlight to see them clearly.

Step 2: Remove the Screws

Once you’ve located the screws, use a screwdriver to remove them. Be sure to keep the screws in a safe place, so you don’t lose them.

Step 3: Lift the Cover

With the screws removed, you should be able to lift the cover off of the gear shift. If the cover is stuck, you may need to use a flathead screwdriver to gently pry it loose.

Step 4: Disconnect the Wiring

If your 2010 Toyota Tacoma is equipped with a manual transmission, you may need to disconnect the wiring that connects the gear shift to the transmission. To do this, simply unplug the wiring harness from the back of the gear shift.

Step 5: Remove the Cover

With the wiring disconnected, you should be able to remove the cover completely. Be sure to set it aside in a safe place, so you don’t lose it.

Step 6: Reassemble

To reassemble the gear shift cover, simply follow these steps in reverse order. First, reattach the cover to the gear shift. Then, reconnect the wiring harness if necessary. Finally, use your screwdriver to reattach the screws that hold the cover in place.

In conclusion, removing the cover of the gear shift of a 2010 Toyota Tacoma is a simple process that can be completed in just a few minutes. By following these six easy steps, you can remove the cover quickly and easily, without damaging your vehicle. So, if you’re looking to make a repair or upgrade to your gear shift, don’t hesitate to give it a try. With a little bit of patience and some basic tools, you can get the job done in no time.<h2 id="wpaicg-diy-how-to-remove-the-gear-shift-cover-of-a-toyota-tacoma”>DIY: How to Remove the Gear Shift Cover of a Toyota Tacoma

Are you tired of the worn-out gear shift cover on your 2010 Toyota Tacoma? Do you want to replace it with a new one? Removing the gear shift cover may seem like a daunting task, but it’s actually quite simple. In this article, we’ll guide you through the process of removing the gear shift cover of your Toyota Tacoma.

Before we begin, make sure you have the necessary tools. You’ll need a flathead screwdriver, a Phillips head screwdriver, and a pair of pliers. Once you have these tools, you’re ready to start.

Step 1: Remove the Shift Knob

The first step is to remove the shift knob. To do this, simply twist the knob counterclockwise until it comes off. If the knob is stuck, you can use pliers to help you twist it off. Be careful not to damage the knob or the gear shift.

Step 2: Remove the Shift Boot

Once the shift knob is removed, you’ll need to remove the shift boot. The shift boot is the cover that surrounds the gear shift. To remove it, use a flathead screwdriver to pry up the edges of the boot. Be careful not to damage the boot or the gear shift. Once the edges are lifted, you can pull the boot off.

Step 3: Remove the Center Console

With the shift boot removed, you’ll need to remove the center console. The center console is the piece that surrounds the gear shift and houses the cup holders and storage compartment. To remove it, use a Phillips head screwdriver to remove the screws that hold it in place. There are usually four screws, two on each side of the console. Once the screws are removed, you can lift the console up and out of the way.

Step 4: Remove the Gear Shift Cover

With the center console removed, you can now remove the gear shift cover. The cover is held in place by clips, so you’ll need to use a flathead screwdriver to gently pry the cover off. Start at one corner and work your way around the cover, prying up the clips as you go. Be careful not to damage the cover or the gear shift.

Step 5: Install the New Gear Shift Cover

Once the old gear shift cover is removed, you can install the new one. Simply line up the clips on the new cover with the holes on the gear shift and press it into place. Make sure the cover is securely in place before moving on to the next step.

Step 6: Reassemble the Center Console

With the new gear shift cover installed, you can now reassemble the center console. Start by placing the console back into position and securing it with the screws. Once the console is in place, you can reattach the shift boot and shift knob.

In conclusion, removing the gear shift cover of a 2010 Toyota Tacoma is a simple process that can be done with a few basic tools. By following these steps, you can replace your worn-out gear shift cover with a new one and give your Tacoma a fresh look. Remember to be careful when removing and installing the cover to avoid damaging the gear shift or other components. With a little patience and attention to detail, you can successfully remove and replace the gear shift cover of your Toyota Tacoma.<h2 id="wpaicg-expert-tips-from-a-toyota-mechanic-removing-the-gear-shift-cover-of-a-2010-tacoma”>Expert Tips from a Toyota Mechanic: Removing the Gear Shift Cover of a 2010 Tacoma

If you’re looking to remove the gear shift cover of your 2010 Toyota Tacoma, you’ve come to the right place. As a Toyota mechanic, I’ve seen my fair share of gear shift covers and I’m here to share some expert tips on how to remove it without causing any damage.

Firstly, it’s important to note that the gear shift cover is designed to protect the internal components of the gear shift mechanism. Therefore, it’s crucial to handle it with care to avoid any damage to the parts underneath.

To begin, you’ll need a few tools to help you with the process. These include a flathead screwdriver, a Phillips head screwdriver, and a pair of pliers. Once you have these tools ready, you can start the process of removing the gear shift cover.

The first step is to locate the screws that hold the cover in place. In most cases, there are two screws located at the bottom of the cover. You’ll need to use the Phillips head screwdriver to remove these screws. Once you’ve removed the screws, you can gently pull the cover away from the gear shift mechanism.

However, in some cases, the cover may be held in place by clips instead of screws. If this is the case, you’ll need to use the flathead screwdriver to carefully pry the cover away from the clips. It’s important to be gentle when doing this to avoid damaging the clips or the cover.

Once you’ve removed the cover, you may notice that there is a rubber boot that covers the gear shift mechanism. This boot is designed to keep dirt and debris from entering the gear shift mechanism. If you need to remove the boot, you can do so by gently pulling it away from the gear shift mechanism.

If you’re having trouble removing the cover or the boot, you can use a pair of pliers to help you. However, it’s important to be careful when using pliers to avoid damaging any of the parts.

Once you’ve removed the cover and the boot, you can clean the gear shift mechanism and the surrounding area. This is a good opportunity to inspect the parts for any signs of wear or damage. If you notice any issues, it’s best to have them repaired by a professional mechanic.

When you’re ready to reassemble the gear shift cover, simply reverse the steps you took to remove it. Start by placing the rubber boot back in place and then carefully align the cover with the gear shift mechanism. Once the cover is in place, you can secure it with the screws or clips.

In conclusion, removing the gear shift cover of a 2010 Toyota Tacoma is a relatively simple process that can be done with a few basic tools. However, it’s important to handle the cover and the surrounding parts with care to avoid any damage. If you’re unsure about any aspect of the process, it’s best to consult a professional mechanic for assistance.<h2 id="wpaicg-solving-the-mystery-how-to-remove-the-cover-of-the-gear-shift-in-a-toyota-tacoma”>Solving the Mystery: How to Remove the Cover of the Gear Shift in a Toyota Tacoma

Are you having trouble removing the cover of the gear shift in your 2010 Toyota Tacoma? Don’t worry, you’re not alone. Many people struggle with this task, but with a little guidance, you can easily remove the cover and access the inner workings of your gear shift.

First, let’s talk about why you might need to remove the cover in the first place. There are a few reasons why you might want to do this. Perhaps you need to replace a broken part, or maybe you just want to clean the area underneath the cover. Whatever your reason, the process is relatively simple.

To begin, you’ll need a few tools. You’ll need a flathead screwdriver, a Phillips head screwdriver, and a pair of pliers. Once you have these tools, you’re ready to get started.

The first step is to remove the shift knob. This is the part of the gear shift that you hold onto when you’re changing gears. To remove it, simply twist it counterclockwise until it comes off. If it’s stuck, you can use a pair of pliers to help you twist it off.

Next, you’ll need to remove the center console. This is the part of the car that surrounds the gear shift and houses the cup holders and other features. To remove it, you’ll need to locate the screws that hold it in place. These screws are usually located underneath the cup holders or in the storage compartment. Once you’ve located the screws, use your Phillips head screwdriver to remove them.

Once the screws are removed, you should be able to lift the center console up and out of the way. Be careful not to damage any wires or cables that might be attached to it. If there are any wires or cables attached, you’ll need to disconnect them before you can fully remove the center console.

With the center console out of the way, you should be able to see the cover of the gear shift. This cover is held in place by a few clips and screws. Use your flathead screwdriver to gently pry the clips loose. Be careful not to damage the clips or the cover itself.

Once the clips are loose, you should be able to lift the cover up and off of the gear shift. If there are any screws holding it in place, use your Phillips head screwdriver to remove them.

Congratulations, you’ve successfully removed the cover of the gear shift in your 2010 Toyota Tacoma! Now you can access the inner workings of your gear shift and make any necessary repairs or cleanings.

When you’re ready to put everything back together, simply reverse the steps that you took to remove the cover. Make sure that all screws and clips are securely in place before you reattach the center console and shift knob.

In conclusion, removing the cover of the gear shift in a 2010 Toyota Tacoma might seem like a daunting task, but with the right tools and a little patience, it’s a relatively simple process. Just remember to take your time and be careful not to damage any parts along the way. With a little practice, you’ll be able to remove and replace the cover of your gear shift like a pro!<h2 id="wpaicg-quick-and-easy-removing-the-gear-shift-cover-of-a-2010-toyota-tacoma”>Quick and Easy: Removing the Gear Shift Cover of a 2010 Toyota Tacoma

If you’re looking to remove the gear shift cover of your 2010 Toyota Tacoma, you’ve come to the right place. This process is quick and easy, and can be done with just a few simple tools. In this article, we’ll guide you through the steps to remove the gear shift cover of your 2010 Toyota Tacoma.

First, you’ll need to gather the necessary tools. You’ll need a flathead screwdriver, a Phillips head screwdriver, and a pair of pliers. Once you have these tools, you’re ready to begin.

The first step is to remove the shift knob. To do this, simply grasp the knob firmly and pull upwards. It may take some effort, but the knob should come off easily. If it’s stuck, you can use a pair of pliers to help you pull it off.

Next, you’ll need to remove the shift boot. This is the cover that surrounds the gear shift and protects it from dirt and debris. To remove the shift boot, you’ll need to locate the clips that hold it in place. These clips are located on the sides of the boot, near the bottom.

Using your flathead screwdriver, gently pry the clips away from the boot. Be careful not to damage the clips or the boot itself. Once the clips are loose, you should be able to lift the boot off of the gear shift.

With the shift boot removed, you’ll now be able to access the screws that hold the gear shift cover in place. There are two screws that need to be removed – one on the left side and one on the right side.

Using your Phillips head screwdriver, remove these screws. Be sure to keep them in a safe place so you don’t lose them. Once the screws are removed, you should be able to lift the gear shift cover off of the console.

Congratulations! You’ve successfully removed the gear shift cover of your 2010 Toyota Tacoma. Now you can clean or replace the cover as needed. To reassemble, simply follow these steps in reverse order.

In conclusion, removing the gear shift cover of a 2010 Toyota Tacoma is a quick and easy process that can be done with just a few simple tools. By following these steps, you’ll be able to access the gear shift and make any necessary repairs or replacements. Remember to be careful when removing the shift knob and shift boot, and to keep track of the screws so you don’t lose them. With a little bit of patience and some basic tools, you’ll have your gear shift cover removed in no time.<h2 id="wpaicg-no-more-guesswork-how-to-remove-the-cover-of-the-gear-shift-in-your-toyota-tacoma”>No More Guesswork: How to Remove the Cover of the Gear Shift in Your Toyota Tacoma

Are you tired of guessing how to remove the cover of the gear shift in your 2010 Toyota Tacoma? Look no further! In this article, we will guide you through the process step-by-step.

First, locate the gear shift cover. It is located in the center console of your Tacoma, just in front of the armrest. The cover is held in place by clips, so you will need to use a flathead screwdriver to gently pry it off.

Once you have removed the cover, you will see the gear shift assembly. The assembly is held in place by a few bolts, which you will need to remove using a socket wrench. Be sure to keep track of the bolts and their locations, as they may vary in size.

Next, you will need to disconnect the wiring harness that connects the gear shift assembly to the rest of the vehicle. To do this, simply press down on the tab located on the harness and pull it away from the assembly.

With the bolts and wiring harness removed, you can now lift the gear shift assembly out of the center console. Be sure to lift it straight up to avoid damaging any of the surrounding components.

Once the gear shift assembly is removed, you can now access the cover that you were originally trying to remove. The cover is held in place by a few more clips, so you will need to use your flathead screwdriver to gently pry it off.

With the cover removed, you can now clean and inspect the gear shift assembly. If you notice any damage or wear and tear, it may be time to replace the assembly altogether.

To reassemble the gear shift assembly, simply follow the steps in reverse order. Start by reattaching the cover, then carefully lower the assembly back into the center console. Be sure to reconnect the wiring harness and tighten the bolts securely.

Finally, snap the gear shift cover back into place and give it a gentle push to ensure that it is securely attached.

Congratulations! You have successfully removed the cover of the gear shift in your 2010 Toyota Tacoma. With these simple steps, you can now access and inspect the gear shift assembly with ease.

Remember to always use caution when working on your vehicle, and if you are unsure about any step in the process, consult your vehicle’s owner’s manual or a professional mechanic.

By following these steps, you can save time and money by performing simple maintenance tasks on your own. No more guesswork – you now have the knowledge and confidence to remove the cover of the gear shift in your Toyota Tacoma.<h2 id="wpaicg-toyota-tacoma-gear-shift-cover-removal-a-step-by-step-guide”>Toyota Tacoma Gear Shift Cover Removal: A Step-by-Step Guide

If you’re looking to remove the cover of the gear shift of your 2010 Toyota Tacoma, you’ve come to the right place. This process may seem daunting at first, but with the right tools and a little bit of patience, you can easily remove the cover and access the inner workings of your gear shift.

Before you begin, make sure you have the necessary tools on hand. You’ll need a flathead screwdriver, a Phillips head screwdriver, and a pair of pliers. Once you have these tools, you’re ready to get started.

Step 1: Remove the Shift Knob

The first step in removing the cover of your gear shift is to remove the shift knob. To do this, simply grasp the knob firmly and twist it counterclockwise until it comes loose. If the knob is stuck, you may need to use pliers to help loosen it.

Step 2: Remove the Shift Boot

Once the shift knob is removed, you’ll need to remove the shift boot. This is the piece of material that surrounds the base of the shift knob. To remove it, simply grasp the boot and pull it upward. It should come loose easily.

Step 3: Remove the Center Console

With the shift knob and boot removed, you can now move on to removing the center console. This is the piece of plastic that surrounds the gear shift and houses the cup holders and other accessories. To remove it, you’ll need to use your flathead screwdriver to pry it loose.

Start by inserting the screwdriver into the seam between the center console and the dashboard. Gently pry the console upward until it comes loose. Be careful not to use too much force, as you don’t want to damage the console or the dashboard.

Step 4: Remove the Screws

With the center console removed, you’ll now be able to access the screws that hold the gear shift cover in place. There should be two screws located at the base of the cover. Use your Phillips head screwdriver to remove these screws.

Step 5: Remove the Cover

Once the screws are removed, you can now remove the cover itself. Simply grasp the cover firmly and pull it upward. It should come loose easily. If it’s stuck, you may need to use your flathead screwdriver to gently pry it loose.

Step 6: Reassemble

With the cover removed, you can now access the inner workings of your gear shift. If you need to make any repairs or adjustments, now is the time to do so. Once you’re finished, simply reassemble the cover by following these steps in reverse order.

First, replace the cover and secure it with the screws. Next, replace the center console and snap it back into place. Finally, replace the shift boot and shift knob.

In conclusion, removing the cover of the gear shift of a 2010 Toyota Tacoma may seem like a daunting task, but with the right tools and a little bit of patience, it’s a relatively simple process. By following these steps, you’ll be able to access the inner workings of your gear shift and make any necessary repairs or adjustments. So go ahead and give it a try – you’ll be glad you did!<h2 id="wpaicg-get-your-hands-dirty-removing-the-gear-shift-cover-of-a-2010-toyota-tacoma”>Get Your Hands Dirty: Removing the Gear Shift Cover of a 2010 Toyota Tacoma

Are you tired of the boring look of your 2010 Toyota Tacoma’s gear shift? Do you want to add a personal touch to your vehicle’s interior? Well, you’re in luck because removing the gear shift cover is a simple task that you can do yourself. In this article, we’ll guide you through the steps to remove the gear shift cover of your 2010 Toyota Tacoma.

Firstly, you need to gather the necessary tools. You’ll need a flathead screwdriver, a Phillips head screwdriver, and a pair of pliers. Once you have these tools, you’re ready to start.

The first step is to remove the shift knob. To do this, you need to twist the knob counterclockwise until it comes off. If the knob is stuck, you can use pliers to help you twist it off. Be careful not to damage the knob or the gear shift.

Next, you need to remove the shift boot. The shift boot is the cover that surrounds the gear shift. To remove it, you need to use a flathead screwdriver to pry it off. Start at one corner and work your way around the boot until it comes off. Be careful not to damage the boot or the gear shift.

Once you’ve removed the shift boot, you’ll see two screws that hold the gear shift cover in place. Use a Phillips head screwdriver to remove these screws. Be sure to keep the screws in a safe place so that you don’t lose them.

After removing the screws, you can now remove the gear shift cover. To do this, you need to use a flathead screwdriver to pry the cover off. Start at one corner and work your way around the cover until it comes off. Be careful not to damage the cover or the gear shift.

Congratulations! You’ve successfully removed the gear shift cover of your 2010 Toyota Tacoma. Now you can add a personal touch to your vehicle’s interior by customizing the cover or replacing it with a new one.

In conclusion, removing the gear shift cover of a 2010 Toyota Tacoma is a simple task that you can do yourself. All you need are a few tools and some patience. Remember to be careful not to damage any parts of the gear shift or the cover. With these steps, you can easily remove the cover and add a personal touch to your vehicle’s interior.<h2 id="wpaicg-toyota-mechanic-reveals-how-to-remove-the-cover-of-the-gear-shift-in-a-2010-tacoma”>Toyota Mechanic Reveals How to Remove the Cover of the Gear Shift in a 2010 Tacoma

Are you having trouble removing the cover of the gear shift in your 2010 Toyota Tacoma? Don’t worry, it’s a common problem that many car owners face. In this article, we’ll guide you through the process of removing the cover of the gear shift in your 2010 Toyota Tacoma.

Firstly, you need to locate the cover of the gear shift. It’s located in the center console of your car, between the driver and passenger seats. The cover is held in place by clips, so you’ll need to use a flathead screwdriver to pry it off. Be careful not to damage the clips or the cover itself.

Once you’ve removed the cover, you’ll see the gear shift mechanism. The gear shift mechanism is held in place by a bolt, which you’ll need to remove using a socket wrench. Make sure you have the right size socket wrench before you start, as using the wrong size can damage the bolt.

After you’ve removed the bolt, you can then remove the gear shift mechanism from the center console. Be careful not to damage any of the wires or cables that are connected to the mechanism. You may need to disconnect some of these wires or cables before you can remove the mechanism completely.

Once you’ve removed the gear shift mechanism, you can then remove the cover from the mechanism itself. The cover is held in place by clips, so you’ll need to use a flathead screwdriver to pry it off. Be careful not to damage the clips or the cover itself.

After you’ve removed the cover, you can then clean the gear shift mechanism and cover. Use a soft cloth and some cleaning solution to remove any dirt or grime that may have accumulated over time. Be careful not to use any harsh chemicals or abrasive materials, as these can damage the mechanism and cover.

Once you’ve cleaned the gear shift mechanism and cover, you can then reassemble everything. Start by reattaching the cover to the mechanism, making sure that the clips are securely in place. Then, reattach the gear shift mechanism to the center console, making sure that all wires and cables are properly connected.

Finally, reattach the bolt that holds the gear shift mechanism in place, using your socket wrench. Make sure that the bolt is tightened securely, but be careful not to overtighten it, as this can damage the mechanism.

In conclusion, removing the cover of the gear shift in a 2010 Toyota Tacoma is a relatively simple process that can be done with a few basic tools. Just remember to be careful when prying off the cover and removing the gear shift mechanism, and to clean everything thoroughly before reassembling it. With a little bit of patience and care, you can have your gear shift looking and functioning like new in no time!<h2 id="wpaicg-removing-the-gear-shift-cover-of-a-toyota-tacoma-tips-and-tricks-from-a-pro-mechanic”>Removing the Gear Shift Cover of a Toyota Tacoma: Tips and Tricks from a Pro Mechanic

Are you having trouble removing the gear shift cover of your 2010 Toyota Tacoma? Don’t worry, you’re not alone. Many people struggle with this task, but with a few tips and tricks from a pro mechanic, you’ll be able to remove the cover in no time.

Firstly, it’s important to understand why you need to remove the gear shift cover. The cover is usually removed when you need to access the gear shift mechanism for repairs or maintenance. It’s also necessary if you want to replace the gear shift knob or install a new one.

To remove the gear shift cover, you’ll need a few tools. These include a flathead screwdriver, a Phillips head screwdriver, and a pair of pliers. You may also need a small pry bar or a trim removal tool, depending on the type of cover your Tacoma has.

The first step is to locate the screws that hold the cover in place. These screws are usually located on the sides or bottom of the cover. Use your Phillips head screwdriver to remove them. If the screws are tight, you may need to use a pair of pliers to get a better grip.

Once the screws are removed, you can start prying the cover off. Use your flathead screwdriver or trim removal tool to gently pry the cover away from the gear shift mechanism. Be careful not to damage the cover or the surrounding trim.

If the cover is still stuck, you may need to apply some force. Use your pry bar or a larger screwdriver to apply pressure to the cover. Be careful not to apply too much force, as this can damage the cover or the surrounding trim.

Once the cover is removed, you can access the gear shift mechanism. If you need to make repairs or perform maintenance, now is the time to do so. If you’re replacing the gear shift knob, simply unscrew the old one and screw on the new one.

When you’re ready to put the cover back on, simply reverse the steps you took to remove it. Make sure the cover is properly aligned before tightening the screws. If the cover doesn’t fit properly, you may need to adjust it or replace it.

In conclusion, removing the gear shift cover of a 2010 Toyota Tacoma is a relatively simple task that can be done with a few basic tools. By following these tips and tricks from a pro mechanic, you’ll be able to remove the cover in no time. Remember to be patient and careful, and don’t apply too much force. With a little bit of practice, you’ll be able to remove and replace the cover with ease.

Q&A

1. How do I remove the cover of the gear shift of a 2010 Toyota Tacoma?
– First, remove the shift knob by unscrewing it counterclockwise.
2. What tool do I need to remove the shift knob?
– A wrench or pliers can be used to remove the shift knob.
3. After removing the shift knob, what should I do next?
– Remove the center console by unscrewing the screws holding it in place.
4. How many screws hold the center console in place?
– There are usually four screws holding the center console in place.
5. What should I do after removing the screws?
– Lift the center console up and out of the way.
6. What is the next step after removing the center console?
– Remove the gear shift cover by pulling it up and off.
7. Is there anything else I need to remove before I can remove the gear shift cover?
– No, the gear shift cover should come off easily once the center console is removed.
8. Do I need any special tools to remove the gear shift cover?
– No, you should be able to remove the gear shift cover with your hands.
9. Is there anything I should be careful of when removing the gear shift cover?
– Be careful not to damage any wires or cables that may be attached to the cover.
10. Can I reinstall the gear shift cover and center console after removing them?
– Yes, you can reinstall them by reversing the steps you took to remove them.

Conclusion

To remove the cover of the gear shift of a 2010 Toyota Tacoma, first, remove the shift knob by twisting it counterclockwise. Then, remove the center console by unscrewing the screws and gently pulling it up. Finally, remove the cover by unscrewing the screws and gently pulling it up. Be careful not to damage any wires or components while removing the cover. Once the cover is removed, you can access the gear shift mechanism for maintenance or repair.

To remove the cover of the gear shift of a 2010 Toyota Tacoma, follow these steps:
1. Locate the small tab on the bottom of the gear shift cover.
2. Use a flathead screwdriver to gently pry the tab up.
3. Lift the cover off the gear shift.
For more automotive tips and tricks, visit https://best-automechanicschools.com/ and learn from the experts.